Siemens HiPath 1100 Programming Manual Download Page 62

Page: 62 / 241

Step by step

Programming an extension

Agent status after signaling timeout.

Allows you to identify agent’s status at the end of the

signaling timeout.

By default, once the signaling timeout expires the call is

transferred to a different group member and the agent

becomes unavailable (see User Manual - available/un-

available agent for a UCD group).

Required:

Programming mode must be activated (*95

31994).

ekj

Enter the programming code.

Enter the UCD subscriber group number (790 to 799).

Select a status to be displayed for the agent after signal-

ing timeout expires:

= Available

= Unavailable (default)

Enter the next UCD subscriber group number.

Press this key.

Initial status for programming mode.

Cascaded call forwarding

This allows a call to be forwarded up to the third desti-

nation, regardless of the type of call forwarding, i.e.,

destination 1 has call forwarding to destination 2 and

destination 2 has call forwarding to destination 3. Any

call to destination 1 will be forwarded to destination 3.

If destination 3 has call forwarding, the operation will

not be performed.

The destination can be configured with call forward no

answer and/or with unconditional call forwarding.

Independently of the level of call forwarding, if the ex-

tension called has call forward no answer, this will be

called if there is no answer from the destination of the

unconditional call forwarding. If the extension called

does not have call forward no answer, the next call for-

ward no answer in the cascade will be called.

Example:

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands