Siemens HiPath 1100 Programming Manual Download Page 198

Page: 198 / 241

Setup and Installation

198

Setup and Installation

This chapter provides basic instructions and describes procedures for set-

ting up the HiPath 1120 and HiPath 1150. Due to the size of the HiPath 1190

system and the many configuration options installation documentation

must be kept by qualified technical personnel only.

Safety Recommendations

To ensure proper and reliable operation follow these guidelines when set-

ting up your system:

• Install the system in a central location taking into account the length

and extension of cables.

• The location chosen should satisfy the following environmental require-

ments:

- Internal environment with natural air flow of air

- Operation: 23 F to 113 F (-5 C to +45 C), from 5% to 95% RH

• To avoid electrical hazards keep a safety lock on the main distributing

frame of the HiPath 1150.

• Protect against flood, flammable materials, excessive dust, vibration

and mechanical stress.

• Do not install the system where there is a risk of exposure to sunlight,

humidity, heating or cooling sources or proximity to electrical cabling.

• Avoid placing the equipment near data transmission equipment, elec-

trical soldering devices, copy machines, PCs and other electrical equip-

ment that could cause electrical interference

• Install a power outlet for the equipment at a distance of no more than

6.5 feet (2 meters).

• Do not block the natural flow of air around the equipment.

• Do not install inside closets

Important: For South Africa version extension lines with a C/D inter-

face must be installed indoors only. Only regular extensions (with-

out a C/D interface) can be installed outdoors.

Warning: Only service and installation personnel should open the

PABX box and/or connect and handle Line and extension lines.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands