Siemens HiPath 1100 Programming Manual Download Page 87

Page: 87 / 241

Programming an extension

Step by step

Timer for outgoing external calls

This setting specifies a maximum time for the duration

of an outgoing external call for each extension.

The time count starts upon connection of a call and it

never restarts while the call is in progress (e.g., when

there is a transfer). Once the time expires, the call is ter-

minated.

In the default configuration the maximum time for the

duration of outgoing external calls is 180 seconds for all

extensions.

Required:

Programming mode must be activated (*95

31994).

dhk

Enter the programming code.

Enter the extension number (e.g. 11/101).

Enter the length of time for the duration of external calls

for the specified extension (00000 to 17280 in 5-second

cycles), where 00 = 0 seconds... 36 = 180 seconds (de-

fault), etc.

Enter the next extension number.

Press this key.

Initial status for programming mode.

Activate/Disable timer for outgoing external
calls

Required:

Programming mode must be activated (*95

31994).

dhl

Enter the programming code.

Enter the extension number (e.g. 11/101).

Activate/Disable the timer for an outgoing external call:

= Activated

= Deactivated (default)

Initial status for programming mode.

Timeout for external calls

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands