Siemens HiPath 1100 Programming Manual Download Page 37

Page: 37 / 241

Important settings

Step by step

Press this key.

Initial status for programming mode.

Carrier selection mode: LCR or ACS

This allows the user to change carrier selection and use

the best possible option to originate external calls.

Required:

Programming mode must be activated (*95

31994).

ffi

Enter the programming code.

ACS/LCR:

= ACS

= LCR (default)

Initial status for programming mode.

Warning tone for calls without LCR

When the system is configured to use LCR, the HiPath

1100 can alert the user when an external call is being

placed to a destination using a non-default carrier with

rates that may be higher for that time of day. This may

be due to the unavailability of an external line for LCR

(Least Cost Routing).

When using a standard telephone, a warning tone indi-

cates to the user that a different carrier is completing

the call at this time. When using a system telephone,

the carrier’s name will show on the display.

Required:

Programming mode must be activated (*95

31994).

The attendant console does not receive "Direct

message to the speakerphone" and it must not

belong to any associated group.

Only the first attendant Console will be called for

digit 9. The second should be for the extension

number.

When the system is configured with a carrier di-

aling selection mode and is reconfigured to work

with a different selection mode (for example,

ACS >>LCR), all the previous settings are lost.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands