Siemens HiPath 1100 Programming Manual Download Page 73

Page: 73 / 241

Programming an extension

Step by step

Required:

Programming mode must be activated (*95

31994).

egd

Enter the programming code.

de . mm

Enter the length of time (01 to 99 in cycles of 5 seconds)

where 01 = 5 seconds... 06 = 30 seconds (default).

Initial status for programming mode.

Conditional forwarding limited by ex-
tension

Incoming calls can be forwarded to a specified destina-

tion list, as configured in a TAPI-type application such as

a Windows TAPI Browser. The settings of the previous

list or unconditional call forwarding will be replaced with

the new list settings.

The following information is required for configuring a

list:

• Incoming caller ID

• Day of the week and time

• Type of call (internal or external)

When more than one number have been specified for

incoming calls to an extension, the call forwarding prior-

ity will be:

1. Checks to see if the Caller ID for the incoming call

matches the number programmed for the extension

2. Checks to ensure that the Type of Call (internal or ex-

ternal) has been configured

3. Checks the time settings.

Required:

Programming mode must be activated (*95

31994). The extension has permission for a conditional

call forwarding.

dmk

Enter the programming code.

de . id

Enter the number of digits that can be programmed for

extensions with permission (default is 5).

Initial status for programming mode.

This configuration is available through a CTI inter-

face

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands