Siemens HiPath 1100 Programming Manual Download Page 182

Page: 182 / 241

Step by step

Relay and sensor on the HiPath 1120

182

DTMF signals for the sensor

This setting specifies a number sequence that is con-

verted to DTMF signals and sent after a call is an-

swered. The number to be called must be specified in

"Number dialed by sensor activation"

(Code 052).

The default configuration does not specify any number.

Required:

Programming mode must be activated (*95

31994).

ekk

Enter the programming code.

Enter the number sequence (up to 20 digits).

Press this key.

Initial status for programming mode.

Sensor message

After assigning a number, you can assign a message to

the sensor. This message will be transmitted to the as-

signed number when the sensor status is changed.

Required:

Programming mode is activated (*95 31994)

and an EVM Module is installed.

feg

Enter the programming code.

Select a Message:

= Greeting 1

= Greeting 2

Initial status for programming mode.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands