Siemens HiPath 1100 Programming Manual Download Page 39

Page: 39 / 241

Important settings

Step by step

Connection of GSM/SIP boxes with
LCR access

GSM boxes work as if the call were sent from a GSM

cell phone and the SIP boxes work as if the call were

made using a PC. Thus the call can be sent by the

cheapest route according to the analysis of the destina-

tion of the call using the rule configured in the LCR.

It is possible to connect GSM/SIP boxes to the HiPath

1100 using the S

module where the ISDN lines must

be set in a line group according to the carrier type: GSM

or SIP.

Activating the time for LCR fallback

This timer should be activated for routes subject to de-

lays or problems making call connections (for example,

SIP boxes). When the preset time has elapsed, the call

is routed to the Default Carrier defined in that rule of the

LCR (See Manager - A31003-K1160-M810-*, LCR).

Required:

Programming mode must be activated (*95

31994).

fid

Enter the programming code.

lmd

lmm

Enter the number for the group of external lines (e.g: 0,

890)

Activating/Disabling the timer:

= Activated

= Deactivated (default)

Initial status for programming mode.

To install these peripherals, consult the manual

of the respective products and the support tech-

nician.

Summary of Contents for HiPath 1100


















































































































































































































































Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands

Siemens HiPath 1100, Programming Manual

Search results

Summary of Contents for HiPath 1100

Reviews:

Related manuals for HiPath 1100

Brands by name

Popular brands