manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 93 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 93

KH 8384-5 EN 

 93 

Parameter lists

AI FB:

HI_HI_ALM (33)

Read capability r
Alarm for the high-high alarm limit (HI_HI_LIM) including details on the date and time as 

well as the value at which the alarm is triggered.

• 

Unit of PV_SCALE

Note:

 Additionally, the active alarm can be confirmed manually in this parameter group.

AI FB:

HI_HI_LIM (26)

Read/write capability r/w; supported modes ALL
High-high alarm limit (HI_HI_ALM)

• 

Range and unit of PV_SCALE

If PV exceeds this limit, the alarm state parameter HI_HI_ALM is issued.

AI FB:

HI_HI_PRI (25)

Read/write capability r/w; supported modes ALL
Behavior upon exceeding the high-high alarm limit HI_HI_LIM

• 

[0] · The violation of the high-high alarm limit is not analyzed.

• 

1 · No notification upon violation of the high-high alarm limit

• 

2 · Reserved for block alarms

• 

3 to 7 · The violation of the high-high alarm limit is issued to notify the operator with the 

corresponding priority: (3 = low, 7 = high)

• 

8 to 15 · The violation of the high-high alarm limit is issued as a critical alarm with the 

corresponding priority: (8 = low, 15 = high)

AI FB:

HI_LIM (28)

Read/write capability r/w; supported modes ALL
Alarm limit for the high pre-alarm HI_ALM

• 

Range and unit of PV_SCALE, [3402823466 x 10

38

]

If PV exceeds this limit, the alarm state parameter HI_ALM is issued.

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments