manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 35 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 35

KH 8384-5 EN 

 35 

Parameter lists

RES:

MANUFAC_ID (10)

Storage class S; read capability r

Manufacturer ID

• 

[0 x 00E099] · SAMSON AG

RES:

MAX_NOTIFY (31)

Storage class S; read capability r
Number of unconfirmed event reports simultaneously supported by the device.

•  [40]

RES:

MEMORY_SIZE (22)

 · This parameter is not supported.

RES:

MIN_CYCLE_T (21)

Storage class S; read capability r

Shortest cycle time that the device can perform.

• 

[8000 · ms]

RES:

MODE_BLK (5)

Storage class N; read/write capability r/w; supported modes O/A
Mode of the Resource Block

 

– Target Mode 

 Code 48 S0

 

– Actual Mode (read only) 

 Code 48 S1

 

– Permitted Mode

 

– Normal Mode (read only)
• 

AUTO · The execution of the function blocks (AO and PID) is enabled.

• 

O/S · The execution of the function blocks (AO and PID) is stopped. These blocks go out 

of service (O/S mode).

RES:

NV_CYCLE_T (23)

Storage class S; read capability r

Time interval in which device data are stored to the non-volatile memory.

Note:

 Non-volatile data are saved immediately after transmission.

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments