manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 103 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 103

KH 8384-5 EN 

 103 

Parameter lists

PID FB:

DV_LO_PRI (58)

Storage class S; read/write capability r/w; supported modes ALL
Behavior upon falling below the lower set point deviation (DV_LO_LIM)

• 

[0] · The violation of the limit for the lower set point deviation is not analyzed.

• 

1 · No notification upon violation of the limit for the lower set point deviation

• 

2 · Reserved for block alarms

• 

3 to 7 · The violation of the limit for the lower set point deviation is issued to notify the 

operator with the corresponding priority: (3 = low, 7 = high)

• 

8 to 15 · The violation of the limit for the lower set point deviation is issued as a critical 

alarm with the corresponding priority: (8 = low, 15 = high)

PID FB:

FF_GAIN (42)

Storage class S; read/write capability r/w; supported modes M/O

Feedforward gain

•  [0]

Note:

 The feedforward gain is multiplied with the input value (FF_VAL). The result is added 

to the OUT value.

PID FB:

FF_SCALE (41)

Storage class S; read/write capability r/w; supported modes M/O
Measuring range of FF_VAL input value (lower and upper limits, unit and decimal point)

• 

[0 to 100 %]

PID FB:

FF_VAL (40)

Storage class N; read/write capability r/w; supported modes ALL

Feedforward control input value (value and status)

• 

Range and unit of FF_SCALE

Note:

 The input value is multiplied with the feedward gain FF_GAIN. The result is added to 

the OUT value.

PID FB:

GAIN (23)

Storage class S; read/write capability r/w; supported modes ALL
Proportional-action coefficient

•  [1.0]

Note:

 The parameter must be set to a value not equal to 0; otherwise, a configuration 

error is set in the BLOCK_ERR parameter and the block is set to 'Out of service' (O/S) 

mode.

PID FB:

GRANT_DENY (12)

 · This parameter is not supported.

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments