manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 53 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 53

KH 8384-5 EN 

 53 

Parameter lists

AO TRD: FINAL_VALUE_D (49)

Storage class S; read/write capability r/w; supported modes O/M
Discrete set point of upstream DO1 Function Block

AO TRD: FINAL_VALUE_RANGE (15)

Storage class S; read/write capability r/w; supported modes O
Travel/angle range

• 

FINAL VALUE RANGE EU_100 · Travel/angle range end 

 Code 9

• 

FINAL VALUE RANGE EU_0 · Travel/angle range start 

 Code 8

• 

FINAL VALUE RANGE UNITS_INDEX · Unit

• 

FINAL VALUE RANGE DECIMAL · Decimal point

Note:

 FINAL_VALUE is sent to the AO Transducer Block directly from an upstream AO 

Function Block.
The FINAL_VALUE_RANGE operating range is compared on entering it with TRANS_PIN_

POS. If the TRANS_PIN_POS parameter is changed, the positioner checks whether the 

setting and unit match the current operating range FINAL_VALUE_RANGE. If this is not the 

case, the FINAL_VALUE_RANGE operating range is set to 0 to 100 %.

AO TRD: FRICTION (68)

Storage class N; read capability r

Determined friction in percent

AO TRD: FRICTION_LIMITS (265)

Storage class S; read/write capability r/w; supported modes O/M/A
Upper/lower friction limits

• 

FRICTION_LIMIT_UP, 0 to 1000 % [200 %]

• 

FRICTION_LIMIT_DOWN, 0 to 1000 % [50 %]

AO TRD: FRICTION_UNITS (67)

 · This parameter is not supported.

AO TRD: FST_BREAKOUT_TIME (86)

Storage class S; read capability r
Breakaway time determined during the last full stroke test (FST)

AO TRD: FST_BREAKOUT_TIMEOUT (87)

Storage class S; read/write capability r/w; supported modes O/M/A

Cancellation conditions of the full stroke test (FST): maximum breakaway time

•  0.0 to 25000.0 s, [7.5 s]

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments