manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 60 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 60

 60  

KH 8384-5 EN

Parameter lists

AO TRD: LS_TEST_INFORMATION (273)

Storage class D; read capability r

Leakage sensor: test status

AO TRD: MIN_CLEARANCE_NEW_LOGGING_MGV (107)

Storage class S; read/write capability r/w; supported modes O/M/A

Minimum time interval until logging of the internal solenoid valve restarts (error control)

AO TRD: MODE_BLK (5)

Storage class S; read/write capability r/w

Operating mode

 

– Target Mode 

 Code 48 t0

 

– Actual Mode (read only) 

 Code 48 t1

 

– Permitted Mode

 

– Normal Mode (read only)
• 

AUTO · A positioning value is calculated from the output value received from the AO 

Function Block and the control valve is positioned accordingly.

• 

O/S · The positioning value from the AO Function Block is not used. The control valve is 

moved to its mechanical fail-safe position entered in ACT_FAIL_ACTION. The mode is 

also changed to O/S when the forced venting function is activated.

• 

MAN · The positioning value (FINAL_VALUE) can be entered manually (reading at the 

positioner:   and  )

• 

LO · AO TRD switches to LO mode if the positioner is switched to the MAN mode on 

site.

AO TRD: NO_OF_ZERO_POINT_ADJ (137)

Storage class D; read capability r

Number of zero calibrations performed since the last initialization 

 Code 48 d3

AO TRD: OPTI_SUB_INIT (119)

Storage class S; read/write capability r/w; supported modes O/M/A

Optimizes edges of substitute calibration

•  ON
•  [OFF]

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments