manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 34 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 34

 34  

KH 8384-5 EN

Parameter lists

RES:

FIRMWARE_REVISION (65)

Storage class N; read capability r

Firmware version for communication and control

RES:

FREE_SPACE (24)

 · This parameter is not supported.

RES:

FREE_TIME (25)

 · This parameter is not supported.

RES:

GRANT_DENY (14)

Storage class D; read/write capability r/w; supported modes NA
Grant or deny a fieldbus host system access to the field device

Note:

 This parameter is not analyzed by Type 3730-5.

RES:

HARD_TYPES (15)

Storage class S; read capability r

Types of input and output signals (hardware) available for the device

• 

[Scalar Output] · Scalable analog output variable

• 

Scalar Input · Scalable analog input variable

•  Discrete Output
•  Discrete Input

RES:

HW_REVISION (66)

Storage class S; read capability r

Hardware release for electronics and mechanics

RES:

ITK_VER (41)

Storage class S

Version of the Interoperability Tester Kit on which the interoperablity testing is based.

RES:

LIM_NOTIFY (32)

Storage class S; read/write capability r/w; supported modes O/A
Number of unconfirmed event reports simultaneously supported by the device.

•  0 to [40]

RES:

LOCAL_OP_ENA (79)

Storage class N; read/write capability r/w; supported modes O/A

Locks on-site operation

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments