Samson FOUNDATION 3730-5 Configuration Manual Download Page 116

Page: 116 / 128

116

KH 8384-5 EN

Parameter lists

DO FB:

FSTATE_TIME (19)

Storage class S; read/write capability r/w; supported modes ALL

Fault state time [s]

Time between an error in the set point valid for the DO Function Block in the current

operating mode is detected and failure action is triggered.

• [0]

Note:

Failure action is triggered if the error persists after this time has elapsed.

The fault state of the DO Function Block is determined in the IO_OPTS parameter of this

block.

DO FB:

FSTATE_VAL_D (20)

Storage class S; read/write capability r/w; supported modes ALL
Fault state value for the DO Function Block when failure action is triggered.

•

Value and range from PV_SCALE ±10 %, [0]

Note:

The value is used if the FAULT STATE TO VALUE option is selected in the IO_OPTS

parameter.

DO FB:

GRANT_DENY (13)

· This parameter is not supported.

DO FB:

IO_OPTS (14)

Storage class S; read/write capability r/w; supported modes O
Selects the input/output behavior of the DO Function Block.

•

INVERTIERT · Inversion of SP_D

•

SP-PV TRACK IN MAN · SP tracks PV in MAN mode (Actual Mode)

•

SP-PV TRACK IN LO · SP tracks PV in LO mode (Actual Mode)

•

SP TRACK RETAINED TARGET · SP tracks RCAS_IN or CAS_IN depending on the preset

target mode in LO or MAN mode (actual mode). This option has priority over SP-PV

TRACK IN MAN/LO.

•

FAULT STATE TO VALUE · FSTATE_VAL_D is used as the set point when the failure action

is triggered (see FSTATE_VAL_D, FSTATE_TIME)

•

USE FAULT STATE VALUE ON RESTART · FSTATE_VAL_D is used as the set point upon

restarting until a valid value has been entered.

•

TARGET TO MAN IF FAULT STATE ACTIVATED · When failure action is triggered, the

target mode is set to MAN and the original target mode is lost. The block remains in

MAN mode after failure action has been left until the user sets it to the desired

operating mode.

•

USE PV FOR BKCAL_OUT · The PV_D process value is fed back at BKCAL_OUT instead

of the working process value.

Summary of Contents for FOUNDATION 3730-5

































































































































Search results

Summary of Contents for FOUNDATION 3730-5

Reviews:

Samson FOUNDATION 3730-5, Configuration Manual, Page: 116 / 128

Search results

Summary of Contents for FOUNDATION 3730-5

Reviews: