manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 43 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 43

KH 8384-5 EN 

 43 

Parameter lists

9.1 

Advanced Positioner Transducer Block (AO TRD)

AO TRD: ACT_FAIL_ACTION (38)

Storage class S; read/write capability r/w

The fail-safe action of the actuator in the event of a supply air failure is detected 

automatically during initialization.

• 

Air to open (in 0 % position)

• 

Air to close (in 100 % position)

AO TRD: ACT_MAN_ID (39)

Storage class S; read/write capability r/w; supported modes O/M/A

Actuator manufacturer

Identifies the manufacturer of the actuator associated with the positioner

AO TRD: ACT_MODEL_NUM (40)

Storage class S; read/write capability r/w; supported modes O/M/A

Type of the actuator associated with the positioner

AO TRD: ACT_SN (41)

Storage class S; read/write capability r/w; supported modes O/M/A

Serial number of the actuator associated with the positioner

AO TRD: ALARM_OPTION (101)

Storage class S; read/write capability r/w
Alarm setting to activate an output error in AO Function Block

• 

No (never) · No

• 

Local Override · Alarm triggered when the AO TRD is in the LOCAL OVERRIDE mode, 

i.e. the positioner is set locally in the SAFE mode or an internal solenoid valve is 

activated.

• 

MAN · Alarm triggered when AO TRD is in MAN mode.

• 

Block Alarm · Alarm triggered when the AO TRD has a MAINTENANCE NOW block 

error

• 

AO TRD fault state · Alarm triggered when the fault state is active.

• 

AO O/S set fault state · Alarm triggered when the AO Function Block in the O/S mode, 

the valve is moved to the FSTATE_VAL of the AO Function Block.

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments