manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 61 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 61

KH 8384-5 EN 

 61 

Parameter lists

AO TRD: PCC (207)

Storage class S; read/write capability r/w; supported modes O/M/A

Cancellation conditions of the partial stroke test (PST)

• 

PST_ACT_X_CONTROL · Activation of x cancellation condition

• 

PST_X_CONTROL_VALUE · x control value

• 

PST_ACT_DELTA_Y_MONI · Activation of y cancellation condition

• 

PST_DELTA_Y_MONI_VAL · delta y-monitoring value

• 

PST_TOL_BAND_CONTROL · Activate PST tolerance band monitoring

• 

PST_TOL_BAND · PST tolerance band

AO TRD: PMD1 (209) to PMD3 (211)

Storage class D; read capability r

Measured data assessment of the partial stroke test (PST)

PMD1 (209) = Current test
PMD2 (210) = First measured data assessment saved
PMD3 (211) = Second measured data assessment saved

• 

PST_TIME_STAMP · Time stamp for this test

• 

PST_OVERSHOOT_RISING · Overshoot (rising)

• 

PST_DEAD_TIME_RISING · Dead time (rising)

• 

PST_T63_RISING · T63 (rising)

• 

PST_T98_RISING · T98 (rising)

• 

PST_RISE_TI_RISING · Rise time (rising)

• 

PST_SETTL_TI_RISING · Settling time (rising)

• 

PST_OVERSHOOT_FALLING · Overshoot (falling)

• 

PST_DEAD_TI_FALLING · Dead time (falling)

• 

PST_T68_FALLING · T63 (falling)

• 

PST_T98_FALLING · T98 (falling)

• 

PST_RISE_T_FALLING · Rise time (falling)

• 

PST_SETTL_T_FALLING · Settling time (falling)

• 

PST_DELTA_Y · delta y-monitoring (repetition value)

AO TRD: POSITIONER_MODEL (112)

Storage class D; read capability r

Positioner type

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments