manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 56 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 56

 56  

KH 8384-5 EN

Parameter lists

AO TRD: FST_TEST_INFO (235)

Storage class D; read capability r

Current status of the full stroke test (FST)

AO TRD: FST_TEST_STAT1 (274) to FST_TEST_STAT3 (276)

Storage class D; read capability r

Status of the full stroke test (FST)

FST_TEST_STAT1 (274) = Current test
FST_TEST_STAT2 (275) = First saved status
FST_TEST_STAT3 (276) = Second saved status

• 

FST_NO_TEST_AVAILABLE · No test available

• 

FST_MAX_TIME_EXCEEDED · Max. test duration exceeded

• 

FST_TEST_MANUA_CANCEL · Test canceled manually

• 

FST_OUT_OF_MEMORY · Measured data memory full

• 

FST_ABO_INT_SOL_VALVE · Canceled due to internal solenoid valve/forced venting

• 

FST_PRESSURE_FRICTION · Canceled due to supply air/friction

• 

FST_CURRENT_TOO_LOW · Test canceled, insufficient current

AO TRD: HIST (135)

Storage class D; read capability r
Reading in hours (or part thereof)

• 

HIS_T_ZEIT_MIN_TEMPERATURE · Operating hours counter: lowest temperature inside 

the positioner

• 

HIS_T_ZEIT_MAX_TEMPERATURE · Operating hours counter: highest temperature inside 

the positioner

• 

TEMP_PERIOD_TIME_LOW · Time the temperature remained below –40 °C (–40 °F)

• 

TEMP_PERIOD_TIME_HIGH · Time the temperature remained above +80 °C (+176 °F)

AO TRD: HISTOGR_X_SCAN_RATE (150)

Storage class D; read/write capability r/w; supported modes O/M/A

Statistical information > Short-term valve position x histogram: measured values and mean 

value

AO TRD: HISTOGR_X_SHORT (149)

Storage class D; read capability r

Statistical information > Short-term valve position x histogram: scan rate to record valve 

positions

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments