manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 118 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 118

 118  

KH 8384-5 EN

Parameter lists

DO FB:

RCAS_OUT_D (24)

Storage class D; read capability r

Discrete set point after applying the ramp function (value and status)

The RCAS_OUT_D value is provided to the fieldbus host system to perform back-

calculations in case of control mode changes or limited signals.

Note:

 This parameter is only active in RCAS mode.

DO FB:

READBACK_D (16)

Storage class D; read capability r

Current discrete valve position

• 

0: 0 %1: 100 %

• 

2: Intermediate position (0.5 % < x < 99.5 %)

DO FB:

SHED_OPT (23)

Storage class S; read/write capability r/w; supported modes ALL
Behavior upon exceeding the monitoring time (see SHED_RCAS in the Resource Block)
Monitoring of the connection between fieldbus host system and DO Function Block in 

RCAS mode. When the monitoring time has elapsed, DO Function Block switches from the 

RCAS mode to the selected operating mode.

The action to be taken after the fault state ends is also determined.

• 

[UNINITIALIZED]

• 

NORMAL SHED_NORMAL RETURN · On failure of remote connection, change to next 

possible mode until RCAS mode is restored.

• 

NORMAL SHED_NO RETURN · On failure of remote connection, change to next 

possible mode. The block remains in this mode.

• 

SHED TO AUTO_NORMAL RETURN · On failure of remote connection, change to 

AUTO mode until RCAS mode is restored.

• 

SHED TO AUTO_NO RETURN · On failure of remote connection, change to AUTO 

mode. No attempt is made to restore the mode and the block remains in AUTO mode.

• 

SHED TO MANUAL_NORMAL RETURN · On failure of remote connection, change to 

MAN mode until RCAS mode is restored.

• 

SHED TO MANUAL_NO RETURN · On failure of remote connection, change to MAN 

mode. No attempt is made to restore the mode and the block remains in MAN mode.

• 

SHED TO RETAINED TARGET_ NORMAL RETURN · On failure of remote connection, 

the block attempts to attain the retained target mode until RCAS mode is restored.

• 

SHED TO RETAINED TARGET_NO RETURN · On failure of remote connection, the block 

sets the target mode to the retained target mode.

Note:

 This parameter is only active in RCAS mode in the DO Function Block.

 

If the value is set to UNINITIALIZED, the DO Function Block cannot be placed in the RCAS 

mode.

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments