Samson FOUNDATION 3730-5 Configuration Manual Download Page 124

Page: 124 / 128

124

KH 8384-5 EN

Parameter lists

DI FB:

STATUS_OPTS (14)

Storage class S; read/write capability r/w; supported modes O

Status options to determine status handling and processing

•

[UNINITIALIZED]

•

PROPAGATE FAIL FWD · Fault state is passed on to the downstream block

DI FB:

STRATEGY (3)

Storage class S; read/write capability r/w; supported modes O/M/A

Permits strategic grouping and thus faster processing of blocks
[0]

Blocks are grouped by entering the same number in the STRATEGY parameter of each block.

Note:

These data are neither checked nor processed by the DI Function Block.

DI FB:

ST_REV (1)

Storage class N; read capability r

Static revision number (DI)

Note:

The revision number is incremented with each change of a static parameter in the

block.

DI FB:

TAG_DESC (2)

Storage class S; read/write capability r/w; supported modes O/M/A
User-specific text for unique identification and assignment of the block

• Max. 32 characters, [no text]

DI FB:

UPDATE_EVT (18)

Storage class D; read capability r

Indicates whether static block data have been changed, including date and time stamp

Summary of Contents for FOUNDATION 3730-5

































































































































Search results

Summary of Contents for FOUNDATION 3730-5

Reviews:

Samson FOUNDATION 3730-5, Configuration Manual, Page: 124 / 128

Search results

Summary of Contents for FOUNDATION 3730-5

Reviews: