manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 33 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 33

KH 8384-5 EN 

 33 

Parameter lists

RES:

FD_OFFSPEC_MAP (48)

Storage class S; read/write capability r/w
Classification of diagnostic messages with the 'Out of specification' status

RES:

FD_OFFSPEC_MASK (52)

Storage class S; read/write capability r/w
Activation/deactivation of diagnostic messages with the 'Out of specification' status

RES:

FD_OFFSPEC_PRI (60)

Storage class S; read/write capability r/w
Determines the priority of diagnostic messages with the 'Out of specification' status

RES:

FD_RECOMMEN_ACT (64)

Storage class D; read/write capability r
Recommended action

RES:

FD_SIMULATE (63)

Storage class S; read/write capability r/w

Simulation of diagnostic messages

RES:

FD_VER (42)

Storage class S; read/write capability r
Field diagnostic specification version

•  [1]

RES:

FEATURES (17)

Storage class S; read capability r
Additional functions supported by the device, see FEATURES_SEL

RES:

FEATURES_SEL (18)

Storage class S; read/write capability r/w; supported modes O/A

Selects the additional functions supported by the device

• 

REPORTS · Fieldbus host system needs to acknowledge receipt of the event report.

• 

HARD W LOCK · Write lock switch hardware is assessed.

• 

FAULTSTATE · Fault state can be triggered (see SET_FSTATE/CLR_FSTATE).

• 

OUT READBACK · Current valve position issued in the PV parameter of the Analog 

Function Block (otherwise in SP parameter).

Note:

 If the AO Function Block is not to move to the MAN mode when the forced venting 

function is activated or the solenoid valve is triggered, deactivate this option.

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments