Samson FOUNDATION 3730-5 Configuration Manual Download Page 41

Page: 41 / 128

KH 8384-5 EN

Parameter lists

Index

Parameters

RESOURCE_BLOCK_2

ST_REV

TAG_DESC

STRATEGY

ALERT_KEY

MODE_BLK

BLOCK_ERR

RS_STATE

TEST_RW

DD_RESOURCE

MANUFAC_ID

DEV_TYPE

Index

Parameters

DEV_REV

DD_REV

GRANT_DENY

HARD_TYPES

RESTART

FEATURES

FEATURE_SEL

CYCLE_TYPE

CYCLE_SEL

MIN_CYCLE_T

MEMORY_SIZE

NV_CYCLE_T

RES:

WRITE_LOCK (34)

Storage class S; read/write capability r/w; supported modes O/A

Status of the write protection switch



Code 47

•

LOCKED · Write protection activated

•

NOT LOCKED · Write protection deactivated

Note:

The write-lock can be activated by setting Code 47 to ON: device data can only be

read over FOUNDATION™ fieldbus communication, but not overwritten.

The write-lock can be deactivated by setting Code 47 to OFF: device data can be

overwritten over FOUNDATION™ fieldbus communication.

RES:

WRITE_PRI (39)

Storage class S; read/write capability r/w; supported modes O/A
Behavior upon a write-lock alarm (WRITE_ALM parameter)

•

[0] · The write-lock alarm is not processed

•

1 · The write-lock alarm is not broadcast to the fieldbus host system.

•

2 · Reserved for block alarms

•

3 to 7 · The write-lock alarm is issued to notify the operator with the corresponding

priority: (3 = low, 7 = high)

•

8 to 15 · The write-lock alarm is issued as a critical alarm with the corresponding priority:

(8 = low, 15 = high)

Index and parameter assignment: Resource Block

Summary of Contents for FOUNDATION 3730-5

































































































































Search results

Summary of Contents for FOUNDATION 3730-5

Reviews:

Samson FOUNDATION 3730-5, Configuration Manual, Page: 41 / 128

Search results

Summary of Contents for FOUNDATION 3730-5

Reviews: