manualshive.com logo in svg

Samson FOUNDATION 3730-5, Configuration Manual, Page: 58 / 128

Share
Download
Samson FOUNDATION 3730-5 Configuration Manual Download Page 58

 58  

KH 8384-5 EN

Parameter lists

AO TRD: INIT_WITH_REF_TEST (117)

Storage class S; read/write capability r/w
Record diagnostic reference tests during initialization.

•  Yes
•  [No]

AO TRD: INTERNAL_TEMP (96)

Storage class D; read capability r

Current temperature inside the positioner

AO TRD: INTERNAL_TEMP_MAX (98)

Storage class D; read capability r

Highest temperature measured inside the positioner

AO TRD: INTERNAL_TEMP_MIN (97)

Storage class D; read capability r

Lowest temperature measured inside the positioner

AO TRD: INTERNAL_TEMP_UNITS (99)

Storage class S; read/write capability r/w; supported modes O/M/A
Unit of temperature inside the positioner: [°C], °F

AO TRD: KP_STEP (127)

Storage class S; read/write capability r/w
Proportional-action coefficient Kp level 

 Code 17

Note:

 This parameter can only be read over FOUNDATION fieldbus. The value is recorded 

during initialization.

AO TRD: LIMIT_VALUE_TIME_ANALYSIS (145)

Storage class S; read/write capability r/w; supported modes O/M/A
Statistical information > Open/close: time limit for difference between reference value and 

currently recorded value
Determines at which value a message is generated.

•  0.0 to 30.0 s, [0.6 s]

AO TRD: LIMIT_VALUE_TRAVEL_ANALYSIS (146)

Storage class S; read/write capability r/w; supported modes O/M/A
Statistical information > Open/close: travel limit for difference between reference value 

and currently recorded value
Determines at which value a message is generated.

• 

0.0 … 100.0 %, [0.3 %]

Summary of Contents for FOUNDATION 3730-5

































































































































Reviews:

No comments