Riso RZ2xx Series Technical Manual Download Page 333 | Manualshive

Page: 333 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 17: TEST MODE

[ 17 - 21 ]

No.

Data setting

Details

Description

Sets the print drum color information on the EEPROM of the Drum PCB.

Setting

Range :                       0:  (not specified)                   13: Yellow
                                     1:  Black                                 14: Light Grey
                                     2:  Blue                                   15: Grey
                                     3:  Medium Blue                    16: Flourescence Pink
                                     4:  Red                                   17: Flourescence Orange
                                     5:  Bright Red                         18: Orange
                                     6:  Riso Federal Blue             19: Flat Gold
                                     7:  Purple                                20: Hunter Green
                                     8:  Riso Marine Red                21: Crimson
                                     9:  Burgundy                           30: Custom
                                   10:  Green                                 31: Order (with specified paper)
                                   11:  Teal                                    32: Order (without specified paper)
                                   12:  Brown                                 63: Any Color

Default : 0 (not specified)

Description

Input the number imprinted on the sticker on the Scanner Unit.

Setting

Range :                       68 to 188 [RZ3 series]
Unit :                           1
Default :                      128

Description

Input the number imprinted on the sticker on the Scanner Unit.

Setting

Range :                       92 to 164 [RZ3 series]
Unit :                           1
Default :                      128

Description

Input the number imprinted on the sticker on the Scanner Unit.

Setting

Range :                      0 to 100
Unit :                           1
Default :                      50

Description

Input the number imprinted on the sticker on the Scanner Unit.

Setting

Range :                      0 to 255
Unit :                           1
Default :                      128
                                    Note: The input number changes after the offset adjustment is made.
                                             Use the newly displayed number from the next offset adjustment for
                                             that one particular scanner unit.

1214

Drum Color Code Entry

1220

Scanner Adjustment (1) Sub-Scanning [for RZ3 series]

1221

Scanner Adjustment (2) Main-Scanning [for RZ3 series]

1222

Scanner Adjustment (3) Sub-Scanning Ratio [for RZ3 series]

1223

Scanner Adjustment (4) Offset [for RZ3 series]

«
...
331
332
333
334
335
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: ureach Pages: 24

Brand: e3works Pages: 38

1:16 USB 3.0 Copy Tower 330110

Brand: Aleratec Pages: 2

Copywriter Flash Duplicator

Brand: MicroBoards Technology Pages: 13

Brand: Disc Makers Pages: 13

Brand: Disc Makers Pages: 14

Brand: Disc Makers Pages: 26

Brand: Disc Makers Pages: 31

Brand: Codonics Pages: 27

Brand: Codonics Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands