manualshive.com logo in svg

Riso RZ2xx Series, Technical Manual, Page: 235 / 374

Share
Download
Riso RZ2xx Series Technical Manual Download Page 235

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 14:  MASTER MAKING SECTION

[ 14 - 3 ]

2. Set Detection Mechanism

Master making unit set detection mechanism

As flatbed section cannot be opened or closed, the unit has a mechanism in which the master making unit
can be pulled out.

The pulling out and insertion of the master making unit are conducted at print drum position-B stop position.
The master making U safety switch and the master making U lock sensor confirm that  the master making
unit is set.

When the master making U safety switch turns OFF, the main motor, clamp motor, master removal compression
motor and master removal transport motor are electrically designed not to activate.

The master making unit upper cover detection mechanism

The master making unit upper cover set sensor confirms that the master making unit upper cover is set, and
the master setting operation is performed once the cover is set.

Master end detection

The end of the master roller is confirmed by the master end sensor detecting the black end mark attached on
the tail end of the master material on the master roll.   The master end sensor checks every 10 ms while the
master is being transported, and the master roll LED on the operation panel illuminates when the end mark
is detected twice in succession.

Master making unit

Master making U safety SW

Master making U lock sensor

1402

1403

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments