manualshive.com logo in svg

Riso RZ2xx Series, Technical Manual, Page: 259 / 374

Share
Download
Riso RZ2xx Series Technical Manual Download Page 259

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 14:  MASTER MAKING SECTION

[ 14 - 27 ]

14.  Removing the Clamping Guide Roller

(1) Pull out the master making unit and switch off the machine power.

(2) Open the master making unit upper cover and remove the master making cover front.

(3) Detach the master loading guide by removing screws (M3x6: 2pcs).

(4) Detach the spur gear by removing screws (M3x8: 1pc).

(5) Detach the snap ring from the rear side, unhook the metal bushing from the rear side frame and slide it

inward.  Slide the clamping guide roller towards the rear and unhook the metal bushing from the front side
frame.  Remove the clamping guide roller from the machine.

Snap ring

Master loading guide

Spur gear

Clamping guide roller

Clamping guide roller

< Front >

< Rear >

1452

1453

1454

1455

Metal bushing behind the snap ring

Metal bushing

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments