Riso RZ2xx Series Technical Manual Download Page 171 | Manualshive

Page: 171 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 10: MASTER REMOVAL SECTION

[ 10 - 3 ]

2. Master on the Drum Check Mechanism (Before Master Removal)

When creating a confidential or normal master, the print drum makes one rotation from its position-B. During
this rotation, the Master sensor checks for the presence of the master on the drum at 40 degrees turn from
position-A. If a master is found on the drum, the machine makes the master removal action with the master
removal sensor active. If no master is found, the master removal action is made with the master removal
sensor deactivated.

The default position of 40 degrees from position-A to check the presence of master on the drum can be
changed by test mode No. 940.

If the machine already knows that there is a master on the drum before going into master making operation,
the master on the drum check action is skipped, and the print drum starting the rotation from the position-B
goes immediately into master removal action.

1004

Drum angle
40 degrees

Master sensor

Anti-reflection cloth

«
...
169
170
171
172
173
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: ANOLY Pages: 24

Brand: Xerox Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands