manualshive.com logo in svg

Riso RZ2xx Series, Technical Manual

The Riso RZ2xx Series Technical Manual is a comprehensive user guide designed specifically for owners of Riso RZ2xx printers. This manual provides precise instructions and detailed information on utilizing the printer's features effectively. Easily download this invaluable resource for free from our website manualshive.com.

Share
Download
background image

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 11:  FB ORIGINAL SCANNING SECTION (600 dpi)

[ 11 - 11 ]

5. Removing the CCD Unit

(1) Switch off the machine power and remove the stage glass.

(2) Remove screws (M3x6: 3pcs) and detach the CCD cover.

(3) Disconnect the CCD cable from the CCD PCB while supporting the PCB firmly by hand.

(4) Remove screws (M3x6: 3pcs) and detach the CCD unit.

< CCD Unit Installation Procedure >

(1) The replacement CCD unit is pre-adjusted at the factory with the positioning brackets attached on the left

and right of the unit for a correct positioning.  Therefore, fit the holes on the positioning brackets into  the
positioning pins on the scanner unit, and secure the CCD unit in place using three screws.

(2) After the CCD unit is firmly screwed onto the scanner unit, unscrew and detach the positioning brackets

off the left and right of the CCD unit.

(3) Connect the CCD cable onto the CCD PCB while supporting the PCB firmly by hand.

< Precautions in Assembly >

To prevent damages to the CCD PCB, firmly support the PCB by hand while connecting or disconnecting the
CCD cable to the PCB.

CCD cover

CCD PCB

CCD PCB

CCD Unit

Positioning bracket

Positioning bracket

CCD Unit

CCD cable

1116

1117

1118

CCD cable

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Teac CD-R-Dupli-4 User Manual preview
CD-R-Dupli-4
Brand: Teac Pages: 34
Carry Pro118 User Manual preview
Pro118
Brand: Carry Pages: 21

Brands by name

Popular brands

Load more brands