Riso RZ2xx Series Technical Manual Download Page 334 | Manualshive

Page: 334 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 17: TEST MODE

[ 17 - 22 ]

No.

Data setting

Details

Description

Input the number imprinted on the sticker on the Scanner Unit.

Setting

Range :                      0 to 255
Unit :                           1
Default :                      128
                                    Note: The input number changes after the gain adjustment is made.
                                              Use the newly displayed number from the next gain adjustment for
                                             that one particular scanner unit.

Description

Activates or deactivates the RLP feature.

Setting

0 : Disabled (default)
1: Enabled

Description

Sets the TPH master-making position to the center

Setting

Range :                      -23 to +23 (-2.3  to  +2.3mm)  [RZ3 series]
                                   -30 to +30 (-3.0  to  +3.0mm) [RZ2 series]
                                   (+ brings the master-making image to the left)
Unit :                           1 (0.1 mm)
Default :                      0 (0 mm)

Description

Sets TPH resistance.

Setting

Range :                      1200 ohm  to  2300 ohm  [RZ3 series]
                                   1200 ohm  to  1900 ohm  [RZ2 series]
Unit :                           1 (1 ohm)
Default :                      1200 (1200 ohm)

1234

TPH resistance input

1233

TPH master-making horizontal position adjustment

1224

Scanner Adjustment (5) Gain [for RZ3 series]

1229

RLP Mode Enable Control [for RZ3 series]

«
...
332
333
334
335
336
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

107756 - Dupli Disc DVD121

Brand: LaCie Pages: 2

kclone-11hd-twr

Brand: Kanguru Pages: 31

Brand: Teac Pages: 1

Brand: Teac Pages: 34

Brand: Teac Pages: 30

Brand: Lanier Pages: 128

AMIGO II EVEREST

Brand: Rimage Pages: 4

Brand: Rimage Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands