Riso RZ2xx Series Technical Manual Download Page 45

Page: 45 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 3: MAIN DRIVE

[ 3 - 7 ]

0309

0310

1. Removing the Pressure Spring

(1) Run Test mode No.908 ( Pressure control maintenance positioning adjustment), unplug the print drum

and switch off the machine power.

(2) Remove the rear cover and swing open the mechanical control & power supply PCB bracket.

(3) Push the pressure lever over to the right and unhook the pressure solenoid lever from the pressure lever.

Then return the pressure lever slowly to the left.

(4) Detach the pressure spring from the pressure lever after removing the other end from the pressure

spring tension plate.

Pressure lever

Pressure spring tention plate

Pressure spring

Pressure solenoid lever

Pressure lever

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Search results

Summary of Contents for RZ2xx Series

Reviews:

Related manuals for RZ2xx Series

Brands by name

Popular brands

Riso RZ2xx Series, Technical Manual

Search results

Summary of Contents for RZ2xx Series

Reviews:

Related manuals for RZ2xx Series

Brands by name

Popular brands