Riso RZ2xx Series Technical Manual Download Page 221 | Manualshive

Page: 221 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 13: AF SCANNING SECTION

[ 13 - 5 ]

3. AF Original Scanning Mechanism

After the AF original setting operation is completed and if the Start key is pressed for the scanning operation,
the scanner lamp turns ON.

The FB read pulse motor activates immediately to move the lamp carriage to the shading compensating
position, and the shading compensation is done. Then the FB read pulse motor rotates the other way and
brings the lamp carriage to the AF scanning position and stops.

At the same time, the AF read pulse motor rotates in the forward direction to bring the original 29.9mm from
the point in which the AF read sensor turned ON and stops. The AF read pulse motor starts to feed the
original through the AF unit and the read-signal goes ON to start the scanning. As the tail end of the original
goes out of the original read sensor the read-signal goes OFF to end the scanning. (If the operator has
chosen a print paper size smaller than the original, the read-signal turns OFF after scanning for that size.)
After the read-signal turns OFF, the AF read pulse motor rotates at a fast speed to eject the original out. After
a given period of time from the point in which the AF original ejection sensor detects the original gone out, the
AF read pulse motor stops to end the AF original scanning movement.

Original ejection roller

AF read sensor

Registration roller

AF original
ejection sensor

Read roller

Original OUT

White plate used for
shading compensation

AF Scanning window

Anti-reflection sheet

1303

«
...
219
220
221
222
223
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: Addonics Technologies Pages: 8

Brand: Teac Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands