Riso RZ2xx Series Technical Manual Download Page 20 | Manualshive

Page: 20 / 374

background image

RISO Inc. Technical Communications

us.riso.com

[ 2 - 4 ]

CHAPTER 2: MACHINE SUMMARY

(1) When the print drum rotates, the scraper roller and

pickup roller also turn to feed paper. The stripper pad
allows only one sheet to pass through to the second
paper-feed area.

(2) The paper sent from the first paper-feed area contacts

the timing roller and guide roller, and stops temporarily.
This causes slight buckling of the paper.

(3) The timing roller and guide roller start rotating, feeding

paper to the pressure section. (This operation is
referred to as the “second paper-feed”. To prevent
tension from being placed on the end of the paper, the
scraper roller and pickup roller are free to spin.)

(4) When the paper is fed further in from the second paper-

feed area, the pressure roller rises to clamp the paper
between the drum and pressure roller to start the
printing operation.

(5) The printed paper is removed from the print drum by

the separator and separation fan. When the pressure
roller rises, the guide roller also moves up to prevent
tension from being placed on the tailing end of the
paper.

(6) Then, the suction fan sucks in the air to keep the paper

firmly on the transfer belts while the paper is carried to
the paper-receiving tray.

(7) The next sheet of paper is sent to the first paper-feed

area, and the guide roller lowers.

3. Outline of Paper-feeding, Printing, and Paper-ejection Operations

Scraper roller

Pickup roller

Stripper pad

Guide roller

Timing roller

Pressure roller

Separation fan

Separator

Transfer belt

0202

«
...
18
19
20
21
22
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: Datatronics Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands