Riso RZ2xx Series Technical Manual Download Page 224 | Manualshive

Page: 224 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 13: AF SCANNING SECTION

[ 13 - 8 ]

3. Removing the Original Stripper Roller

(1) Switch off the machine power and open the AF unit.

(2) Remove the AF cover and close the AF unit.

(3) Remove the original feed roller assembly.

(4) Remove the pickup roller.

(5) Remove the guiding plate.

(6) Remove the snap ring from the left of the stripper roller and slide the stripper roller to the left. Then

remove the E-ring on the right of the snap ring.

(7) Temporarily slide the H-pick arm FR right assembly to the left, and pull out the parallel pin.

(8) Remove the H-pick arm FR right assembly and the stripper roller from the shaft.

* Be careful not to drop the washer mounted on the gear side of the stripper roller.

< Precaution in Assembly >

The original stripper roller must be installed with the correct orientation. Be sure to position the gear of the
original stripper roller to the right as shown on the photograph below.

Install the washer on the gear side of the Original stripper roller.

When joining the parallel pin onto the H-pickup arm FR right assembly, be sure to insert it into the shallower
groove of the H-pick arm FR right assembly.

Guiding plate

Timing belt

Parallel pin

Snap ring

Stripper Roller

E-ring

H-pickup arm FR right assembly

1308

«
...
222
223
224
225
226
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands