manualshive.com logo in svg

Riso RZ2xx Series, Technical Manual, Page: 165 / 374

Share
Download
Riso RZ2xx Series Technical Manual Download Page 165

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 9:  CLAMP UNIT

[ 9 - 5 ]

4. Clamp Plate Master Clamp Mechanism

Once the load pulse motor on the master-making area feeds a set length of the master material onto the print
drum, the clamp motor activates to rotate the clamp cam until the light path of the clamp sensor-A is blocked
by the disc and the light path of the clamp sensor-B becomes unblocked.  This action brings the clamp
opening cam up and closes both the master ejection plate and the clamp plate to clamp the master material
under the clamp plate.  At this stage both the clamp opening cam and position-A compensation plate are
brought up back to their home position.

0908

0909

0910

Position-A compensation plate

Clamp opening cam

Clamp plate

Clamp sensor-B

Clamp sensor-A

Clamp cam

Master ejection plate

Master

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments