Riso RZ2xx Series Technical Manual Download Page 58 | Manualshive

Page: 58 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 4: FIRST PAPER FEED SECTION

[ 4 - 6 ]

4. First Paper Feed Drive Mechanism

When the Start key is pressed for a printing job, the Main motor activates and the drive is transferred by the
main belt to rotate the print drum.

When the print drum rotates to a certain angle from the position-A, the paper feed clutch activates and rotates
the scraper and the pickup rollers, sending the paper on the paper feed tray into the machine.

As the paper is fed into the machine, the leading edge of the paper blocks the light path of the paper sensor.

At a certain drum angle from when the light path of the paper sensor is cut, the paper feed clutch deactivates
and finishes the first paper feeding action. When the first paper feeding ends, the leading edge of the paper is
hitting against the timing roller and guide roller (the two rollers are touching each other and blocking the paper
path), and makes a buckle at the tip.

At the same time the paper feed clutch activates, the paper sensor checks whether the paper is picked up from
the paper feed tray or not. If the paper sensor does not detect the paper coming into the machine, it is judged
that no first paper feeding was made and shows paper jam message.

Both the scraper roller and pickup roller have built-in one-way bearing for a free rotation, allowing the paper to
be picked up by the second paper feed mechanism without the drag of the first paper feed area.

Main belt

Guide roller

Paper feed clutch

Pickup roller

Paper sensor

Scraper roller

Timing roller

Main motor

Pickup roller

Scraper roller

Stripper pad

0410

0411

«
...
56
57
58
59
60
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Intelligent 9 Series

Brand: U-Reach Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands