Riso RZ2xx Series Technical Manual Download Page 274 | Manualshive

Page: 274 / 374

background image

RISO Inc. Technical Communications

us.riso.com

[ 15 - 2 ]

CHAPTER 15: OTHER PRECAUTIONS

1. Power-Saving (Low-Power) Mode

With no error status on the machine, if no operation is made on the machine for 30 seconds, the 24 volt
supply to the machine components is terminated. This must

be kept in mind when using a multi-meter to

check the 24 volts on the machine. Whether the machine is

in the Power-Saving Mode or not can be

confirmed by looking at the heart-beat-LED on the Mechanical

Control PCB. The blinking of the LED is

fast in normal condition, and the slower in the Power-Saving

Mode. The machine will not go into the

Power-Saving Mode when in Test Mode.

2. Software Downloading Procedure

< Software downloading procedure for Mechanical Control PCB >

(1) Switch OFF the machine power.
(2) Remove the download slot cover from the top of the rear cover of the machine by removing screws

(M4x8 :2pcs).

(3) Insert the downloading card containing appropriate software for the mechanical control PCB for the

specific machine model.

(4) Turn ON the machine power. The green LED 1 aside the download slot, as well as the LED on the wake-

up key on the operation panel starts to blink. The program is being downloaded.

(5) When both the green LED 1 and LED on the wake-up key changes from blinking to a solid light, the

program downloading is successfully finished.

* If a red colored LED aside the download slot lights and the wake-up key LED changes to a solid light, the

program downloading went through an error and ended unsuccessfully. The program downloading
procedure must be repeated from the start.

(6) After the program downloading is successfully finished, switch OFF the machine power and remove the

downloading card from the machine.

(7) Mount the download slot cover back on the machine.

< Software downloading procedure for the optional SH3M PCB >

(1) Switch OFF the machine power.
(2) Confirm that the mechanical control PCB and optional SH3M PCB are connected.
(3) Remove the card slot cover located on the rear cover on the paper feed side by removing a screw (M3x6:

1pc).

(4) Insert the downloading card containing the appropriate software for the optional SH3M PCB for the

specific machine model.

(5) Turn ON the machine power. The green LED 1 aside the download slot, as well as the LED on the wake-

up key on the operation panel starts to blink. The program is being downloaded.

* If a red colored LED aside the download slot lights and the wake-up key LED changes to a solid light, the

program downloading went through an error and ended unsuccessfully. The program downloading
procedure must be repeated from the start.

(6) After the program downloading is successfully finished, switch OFF the machine power and remove the

downloading card from the machine.

(7) Mount the download slot cover back on the machine.

< Precaution in Downloading >

- Download the software for the mechanical control PCB bef

ore the software for the optional SH3M PCB.

ore the software for the optional SH3M PCB.

Heart-beat-LED

Mechanical control PCB

1504

«
...
272
273
274
275
276
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: U-Reach Pages: 15

Brand: MF DIGITAL Pages: 12

Brand: MF DIGITAL Pages: 14

Brand: MF DIGITAL Pages: 20

Brand: MF DIGITAL Pages: 24

5000 Platform Series

Brand: MF DIGITAL Pages: 65

Director EC Series

Brand: MF DIGITAL Pages: 87

UNI REMOTE TX4H 433MHZ BLUE

Brand: Communica Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands