manualshive.com logo in svg

Riso RZ2xx Series, Technical Manual, Page: 319 / 374

Share
Download
Riso RZ2xx Series Technical Manual Download Page 319

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 17:  TEST MODE

[ 17 - 7 ]

No.

Sensor switch check

Detection status

0200 Carriage HP sensor

Carriage at  Home position.

0201 Flatbed Original Det. Sensor

Detecting (original present)

0209 Compression plate open/shut sensor

Original Det. Cover closed.

No.

Motor, solenoid

Remarks

0260 Scanner lamp

Switches ON/OFF scanner lamp   [Available only on RZ3 series]

No.

Unit check

Details

0289

0288

0281

Carriage Home Action

Brings the carriage to the Home Position.  (RZ2 series = Scanner carriage,    RZ3 series = Mirror carriage)

Moves the scanner to lamp replacing position.

Scanner HP Positioning & Image sensor adjustment Positioning   [Available only on RZ2 series]

1. Scanner HP positioning.
2. Image sensor adjustment positioning
         Repeats above two positioning by each pressing of START key.

Moves Scanner to the machine shipping position (Same for scanner unit shipping position).

Scanner "Shipping" Positioning

Scanner Lamp Replace Positioning   [Available only on RZ3 series]

RZ3 series : Scanner one cycle action with auto-base-control (ABC) action.
RZ2 series : Scanner one cycle action without the ABC action.
Repeats the one cycle action until the STOP key is pressed.
Presses "Stop" key to stop the motion and returns to Home position.

Scanner Cycle Continuous Action

2. Process /Scanning Test Mode

0284

0287

No.

Data setting

Details

Description 

Sets the slice level for line mode.  Larger  values for lighter print.

Setting 

Range:                       -8 to 8
Unit :                          1
Default :                     0

Description 

Sets the slice level for line mode.  Larger  values for lighter print.

Setting 

Range :                     -16 to 16
Unit :                         1
Default :                    0

Description

Sets the slice level for ABC.  Larger  values for lighter print.

Setting 

Range :                      -16 to 16
Unit :                         1
Default :                    0

Description

Selects the matrix forming the halftone-curve base for photo mode.

Setting 

Range:                      0 to 8
Unit :                         1
Default :                    4

Description

Selects the matrix forming the halftone-curve base for dot mode.

Setting 

Range :                     0 to 8
Unit :                         1
Default :                    4

Description

Selects the matrix forming the halftone-curve base for DotDuo mode.

Setting 

Range :                     0 to 8
Unit :                         1
Default :                    4

Description

Selects the matrix forming the halftone-curve base for DotDuo mode.

Setting 

Range :                     0 to 8
Unit :                         1
Default  :                   4

0340

0350

0351

0340

0341

Halftone Curve Selection (Duo)

Halftone Curve Selection (Dot Photo)   [Available only on RZ3 series]

Halftone Curve Selection (Dot Duo)   [Available only on RZ3 series]

0353

0352

Line-Copy Slice Level Adjustment   [For RZ3 series]

Line-Copy Slice Level Adjustment   [For RZ2 series]

Halftone Curve Selection (Photo)

Auto Base Control (ABC) Slice Level Adjustment   [Available only on RZ3 series]

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments