Riso RZ2xx Series Technical Manual Download Page 301 | Manualshive

Page: 301 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 16: PANEL MESSAGE

[ 16 - 23 ]

Errors involving consumables

Error Type

C01 [Replace ink cartridge]

Description

C01-xxx
No Ink
Replace Ink Cartridge

To reset

display

Remove the empty ink cartridge and replace with a new one.

Error Point

Error Conditions

512

The ink sensor did not go ON even when inking was performed for a preset duration.

563

Ink remaining amount is zero from the information on the RF-Tag.

574

Inkless error was detected 5 times consecutively on one same ink cartridge.

Error Type

C02 [Replace master roll]

Description

C02-xxx
No Master
Replace Master Roll

To reset

display

Remove the empty master roll and replace with a new one.

Error Point

Error Conditions

200

The master end was detected twice in succession at 10-milliseconds intervals during master
transport.

240

Master remaining amount is zero from the RF-Tag information.

253

Masterless error was detected twice consecutively on one same master-roll.

Error Type

C03 [Master disposal box full]

Description

C03-xxx
Master Disposal Box is Full
Empty Master Disposal Box

To reset

display

Remove master disposal box from the machine, throw away the disposed master from the
disposal box and return the disposal box in the machine after a interval of over 5 seconds.

Error Point

Error Conditions

308

Compression detection position was reached before the master-compression-motor encoder-
sensor count reached the specified level, after the master compression motor turned ON in the
compressing direction.

Error Type

C04 [No paper on the paper feed tray]

Description

C04-xxx
Add Paper

To reset

display

Add paper on the paper feed tray.

Error Point

Error Conditions

402

Paper detection sensor is OFF (not detecting paper).

«
...
299
300
301
302
303
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: Hoei Precision Pages: 62

Brand: Aleratec Pages: 38

Brand: StarTech.com Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands