Riso RZ2xx Series Technical Manual Download Page 176

Page: 176 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 10: MASTER REMOVAL SECTION

[ 10 - 8 ]

2. Removing the Master Compression Motor

(1) Switch off the machine power and remove the front cover.

(2) Remove a screw (M3x6: 1pc) and detach the compression gear cover.

(3) As the master compression plate swings down by its weight, remove the spur gear while holding the

compression gear by hand and let the plate swing down slowly.

(4) Detach the helical/spur gear by removing an E-ring.

(5) Remove screws (M3x6: 3pcs) and detach the master compression motor, together with the motor bracket.

(6) Detach the motor from the bracket by removing screws (M3x5: 2pcs).

* Be careful not to lose the white thin plastic spacer on the tip of the worm-gear on the motor shaft.

Helical/spur gear

Compression gear

Spur gear

Master compression motor

Compression motor

Plastic spacer

Motor mounting plate

Motor bracket

Compression gear cover

1013

1014

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Search results

Summary of Contents for RZ2xx Series

Reviews:

Riso RZ2xx Series, Technical Manual, Page: 176 / 374

Search results

Summary of Contents for RZ2xx Series

Reviews: