Riso RZ2xx Series Technical Manual Download Page 324

Page: 324 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 17: TEST MODE

[ 17 - 12 ]

No.

Sensor switch check

Detection status

0600 Paper detection sensor

Sensor light reflected (paper detected)

0601 Paper-size detection sensor

Sensor light reflected (paper detected)

0602 Elevator upper-limit sensor A

[Only for RZ3 series]

Sensor light blocked (Sensor A detecting paper feed tray at maximum up position)

0603 Elevator upper-limit sensor B

Sensor light blocked (Sensor B detecting paper feed tray at maximum up position)

0604 Elevator lower-limit sensor

Sensor light blocked (Sensor detecting paper feed tray at maximum down position)

0605 Paper sensor

Sensor light reflected (paper detected)

0606 Paper-ejection sensor

Sensor light reflected (paper detected)

0607 Paper-feed-tray upper safety SW

Switch ON (paper-feed tray elevation is operational)
Switch OFF (paper-feed tray elevation is non-operational = safety SW is triggered)

0608 Paper-feed-tray lower safety SW

Switch ON (paper-feed tray elevation is operational)
Switch OFF (paper-feed tray elevation is non-operational = safety SW is triggered)

0609 Paper-feed tray elevation button

Switch ON (button is pressed)

0612 Paper-ejection FG sensor

Sensor light blocked (detecting encoder disc)

0614 Paper-feed pressure sensor

Sensor light blocked (detecting paper feed pressure lever)

No.

Motor, solenoid

Remarks

0660 Paper ejection motor

Rotates the motor.

0661 Suction fan

Activates the fan.

0662 Separation fan

Activates the fan.

4. Paper Feed/Eject Test Mode

No.

Unit check

Details

No.

Data check

Details

0721 Paper width potentiometer data

Displays the potentiometer adjustment in millimeter value with the fence set at 297mm width.

No.

Data setting

Details

Description

Selects the paper-feed-tray upper stop position. If 0 (Auto) is selected, the upper limit position is
linked to the paper feed pressure lever position. If 1 to 3 is selected, stop position is fixed.

Setting

Range
0:  Auto (follows Pressure adjust lever)  <Default >
1:  Standard
2: Card
3:  Custom

Elevator upper-limit position selection (for Standard paper finish selection by user-mode). [for RZ3 series]

0688

0740

0708

0681

0683

0682

Paper feed tray elevation up & down

Raises and lowers the paper-feed tray repeatedly

Elevator motor ON action

Rotates the elevator motor for 10 seconds.

[Remove the elevator motor from the machine before activation.]

Paper-feed clutch ON/OFF action

Presses "Start" key to turn ON the clutch. The clutch automatically switches off after 10 seconds.

Paper feed tray maximum down positioning

Raises the paper feed tray to the maximum up position by pressing "START" key.

Paper feed tray maximum up positioning

Lowers the paper feed tray to the maximum down position by pressing by pressing "START" key.

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Search results

Summary of Contents for RZ2xx Series

Reviews:

Riso RZ2xx Series, Technical Manual, Page: 324 / 374

Search results

Summary of Contents for RZ2xx Series

Reviews: