manualshive.com logo in svg

Riso RZ2xx Series, Technical Manual, Page: 185 / 374

Share
Download
Riso RZ2xx Series Technical Manual Download Page 185

RISO Inc. Technical Communications

   us.riso.com

CHAPTER 10:  MASTER REMOVAL SECTION

[ 10 - 17 ]

10. Removing the Pulley Shaft

(1) Switch off the machine power and detach the master removal unit.

(2) Press the master removal roller release lever to release the master removal roller (bottom).

(3) Detach the flanged-gear and pulley shaft gear on the operator’s side of the master removal unit by

removing a snap ring in front of the flanged gear.

(4) Also on the operator’s side of unit, remove a snap ring and unhook the metal bushing from the frame and

slide inward.  Remove the pulley shaft from the unit by pulling it out though the round belts.

1046

1047

1048

Snap ring

Metal bushing

Flanged gear

Snap ring

Pulley shaft

Round belt

Pulley shaft

Pulley-shaft gear

Round belt

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments