Riso RZ2xx Series Technical Manual Download Page 9

Page: 9 / 374

RISO Inc. Technical Communications

us.riso.com

CHAPTER 1: MAINTENANCE

[ 1 - 7 ]

Installation location

Do not install the machine in any of the following locations.

(1) Those subject to direct sunlight or any bright location such as by a window (If you must install in such

a location, put a curtain or the like over the window.).

(2) Those where the temperature changes drastically.

(3) Those that are too hot, cold, humid, or dry.

RECOMMENDED:

Temperature range:

15 degrees Celsius - 30 degrees Celsius

Humidity range:

40% - 70% No condensation allowed

(4) Those with radiant heat sources and any locations in the direct path of air from air conditioners or

heaters.

(5) Any poorly ventilated location.

(6) Dusty atmosphere.

(7) Any tilted location.

(Installation height difference: 10 mm max. front - rear, 10 mm max. left - right).

Electrical connection

- Plug the plug securely into the socket so that there is no problem with the contact in the power

supply plug section.

- Do not use any triplets or extension cords.
- Do not allow any other machine to stand on or crush the power cord.

Ground connection

- Always ground this machine to prevent electrical shock in the unlikely event of electrical leakage.

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Search results

Summary of Contents for RZ2xx Series

Reviews:

Riso RZ2xx Series, Technical Manual, Page: 9 / 374

Search results

Summary of Contents for RZ2xx Series

Reviews: