Riso RZ2xx Series Technical Manual Download Page 316 | Manualshive

Page: 316 / 374

background image

RISO Inc. Technical Communications

us.riso.com

CHAPTER 17: TEST MODE

[ 17 - 4 ]

No.

Data check

Details

0127 AF connection status

Displays whether there is any AF connection.
0: not connected
1: connected (displays program version if ROM is set. Example: Displays "0101" for Ver.1.01

0128 Job Separator connection status

Displays whether there is any Job Separator

connection.

0: not connected
1: connected

0129 NIC connection status

Displays whether there is any NIC

connection.

0: not connected
1: connected

0130 Mechanical control PCB program version display

Displays Mechanical control PCB program version. Example: Displays "0101" for Ver.1.01

0131 ROSA PCB program version display

Displays ROSA program version. Example: Displays "0101" for Ver.1.01

Paper Size ID display

Displays paper ID decided according to paper size VR and paper size detection sensor.
Paper size ID is as follows:

0135 Paper size on feed tray is displayed by ID numbers.

Paper ID Paper description

  00           No paper
  01           A3
  02           B4
  03           A4
  04           A4 landscape
  05           B5
  06           B5 landscape
  07           A5
  08           A5 landscape
  09           B6
  10           B6 landscape
  11           Post card
  12           Post card landscape
  13           Ledger
  14           Legal
  15           Letter
  16           Letter landscape
  17           Statement
  18           Statement landscape
  19           Foolscap
  30           Chinese Paper No. K16
  31           Chinese Paper No. K16 landscape
  32           Chinese Paper No. K8
  50           Paper size undefined 1 (paper size detection sensor : ON)
  51           Paper size undefined 2 (paper size detection sensor : OFF)

0137 Maintenance counter reading (Master Making)

Display of 1 = 100 master makings.
Example: 1234 input = 123,400 master makings.

0138 Maintenance counter reading (Printing)

Display of 1 = 1000 printings.
Example: 1234 input = 1,234,000 prints.

0139 Maintenance counter reading (Print Drum)

Display of 1 = 1000 printings.
Example: 1234 input = 1,234,000 prints.

No.

Data setting

Details

Description

Selection to make the scan/master-making action together with the master-removal-action or to
make the two actions separately.

Setting

0 : Together (default)
1: Independent

Description

Sets the number of masters at which the maintenance-call message is displayed.

Setting

Range :                   0 to 999,900
Unit :                       1 ( x 100)
Default : 0 :            No  maintenance call display

Description

Sets the number of prints at which the maintenance-call message is displayed.

Setting

Range :                   0 to 9,999,000
Unit :                       1 ( x 1000)
Default :                0 : No display maintenance call display

Maintenance-Copy Count Entry

0144

Scan/Master-Making Independent Mode

Maintenance-Master Count Entry

0143

0140

«
...
314
315
316
317
318
...
»

Summary of Contents for RZ2xx Series























































































































































































































































































































































































Reviews:

No comments

Related manuals for RZ2xx Series

Brand: MicroBoards Technology Pages: 2

Brand: Kanguru Pages: 26

Brand: Teac Pages: 16

Brand: Verity Systems Pages: 38

SerialTek Gen5 POD SSAS

Brand: Ellisys Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands