manualshive.com logo in svg

Quasonix HyperTrack, Software Instruction Manual

Share
Download
Quasonix HyperTrack Software Instruction Manual Download Page 89

 

HyperTrack™ 

Software Instruction 

 

80

 

 Quasonix, Inc. 

 

The Azimuth and Elevation axis position display meter breakdown: 

•

 

AZ Axis Velocity readout 

•

 

Actual antenna pointing position 

–

 Orange Pointer, in this case (359.994°) 

•

 

Commanded antenna pointing position 

–

 Blue pointer (under orange pointer) 

•

 

The central, digital, numerical readout for the Commanded and Actual antenna pointing position (both 
indicating 359.994°) 

•

 

CCW and CW limit indicator location 

–

 Not present is a slip ring system (no AZ limits). The EL position 

feedback dial always displays the Up and Down hard (electrical) and soft limits. 

•

 

Slave position digital readout 

–

 Green numerals indicate slave angle(s) are present. Red blanks (- -.- -) 

indicate NO slave angles are present. 

•

 

Analog dial divisions graduated to every 5 degrees (0 to 355.500 degrees) 

The Elevation Status Display includes four LEDs for limits. The user configurable software limits are indicated by 
yellow LEDs and the electromechanical limits by red LEDs that illuminate when reached. The range of the user 
configurable limits are indicated by the red tick marks on the degrees indicator, as shown in Figure 92. After the 
software limits are set, the non-reachable degrees tick marks are blocked in red. 

When the user configurable Multi-Path Clipping (MPC) is enabled, the antenna will not go below lines on the 
degree indicator marked in yellow. In Figure 92, the MPC is set for 0.0°. During a target track, the EL axis will not 
track below 0° when MPC is enabled. 

Note:

 

MPC only applies to the Elevation “

d

own” direction

. 

 

 

Figure 92: Multi-Path Clipping Limit in Yellow 

 

4.2.3.2 

Tracking Error Meter 

The Tracking (Error Meter) is located between the EL and AZ Axis status windows. It provides a visual 

representation of the radiating targets location within the tracking antenna’s beamwidth.

 

The green indicator, shown in the middle of the meter, represents the radiating target relative to the antenna RF field 
of view. This indicator is commonly re

ferred to as the “Meatball

.

”

 

The crosshairs represent the Cartesian Coordinate System. This divides the antenna tracking view into four 
quadrants, as shown in Figure 93. When the green dot/Meatball, is at center or origin of the planes, the target is 
being tracked at optimum. 

Summary of Contents for HyperTrack

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands