PURSUIT T-34C TURBO MENTOR User Manual Download | Manualshive

Page: 85 / 198

background image

86

flange to ensure a good bond). After the
CA cures apply a drop of CA over each
drill hole and let cure.

With the side skin positioned on the fuse
slip the LE of the skin under the cowls.

12. Use an X-acto blade to lightly scribe
a cut line immediately adjacent to the
cowls. Also mark the fuse along the top
and rear edges of the skin with a pen.
Remove the skin and trim along the

scribe line with scissors or an X-acto
knife and straight edge.

13. The LE of the side and top skins
meet at butt joints with the cowl. The
cowl is considerably thicker than the
skins and the specific curvature of the
cowl may vary slightly from the fuse. To
achieve a realistic joint, just follow the
next few steps.

14. Notice that the cowl might fit
snuggly against the fuse in one area
and lift slightly in another (as shown
above). You will be modifying the height
of the side skin to meet the cowl.

To do this, first slide a scrap piece of
.010” polycarbonate, about 3/4” wide,
under the cowls. It should be long
enough to extend from the top fuse
center line to a few inches below the
wing saddle as shown below. This
extension piece (extends the LE of the
side skin) will span the gap from the skin
to the cowl so that the foam fuse will not
show at the panel line.

15. Tape a piece of .010” or .020” thick
scrap plastic, polycarbonate or styrene,
about 8” long x ¾” wide, to the fuse over
the extension strip. The bottom of this
strip should be about even with the wing
saddle. This strip begins the process of
lifting the skin’s LE.

«
...
83
84
85
86
87
...
»

Summary of Contents for T-34C TURBO MENTOR







































































































































































































Reviews:

No comments

Related manuals for T-34C TURBO MENTOR

Brand: Old School Model Works Pages: 24

Brand: Mercedes-Benz Pages: 7

Vac-U-Soling Lower Hull Kit

Brand: Vac-U-Boat Pages: 30

Ju 88C-6b Night Fighter exterior

Brand: Eduard Pages: 6

Education RENEWABLE ENERGY WATER POWERED...

Brand: K'Nex Pages: 20

NORTH AMERICAN T-28 TROJAN

Brand: SG Models Pages: 34

Brand: Amewi Pages: 2

Stirling Mk.I bomb bay

Brand: Eduard Pages: 4

Brand: Trix Pages: 24

DreamWorks ROCK N' TROLL BOOMBOX

Brand: eKids Pages: 12

LASER Sailing Boat & trailer

Brand: REVELL Pages: 12

Brand: VTech Pages: 12

Brand: Nincocean Pages: 12

Brand: Malibu Boats Pages: 200

Brand: PARKZONE Pages: 19

TG726 TURBO RACING CAR KIT

Brand: ThinkGizmos Pages: 36

SERVICING AREA ACCESSORIES

Brand: Faller Pages: 4

Brand: Reely Sky Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands