SG Models NORTH AMERICAN T-28 TROJAN Assembly Manual Download | Manualshive

Page: 1 / 34

background image

Instruction Manual.

1

A S S E M B L Y M A N U A L

Specifications:

Wingspan---------------63.0 in (160 cm).
Wing area---------------349.5 sq.in ( 41.9 sq.dm).
Weight-------------------8.8-9.9 lbs ( 4.0 kg).
Length-------------------50.7 in ( 128.7 cm).
Engine-------------------10-15cc
Motor size---------------1200-1500 Watts
Radio--------------------6 channels with 7 servos.
Electric Power Conversion Included.

“ Graphics and specifications may change without notice ”.

Code: SEA258

1
2
3
...
»

Summary of Contents for NORTH AMERICAN T-28 TROJAN



































Reviews:

No comments

Related manuals for NORTH AMERICAN T-28 TROJAN

Brand: T&J Pages: 11

Brand: Minicraft Models Pages: 4

Little Friendlies Swing & Shake Monkey Rattle

Brand: VTech Baby Pages: 11

Brand: marklin Pages: 32

Brand: Top R/C Hobby Pages: 13

GLUE-N-GO F-4 PP KIT

Brand: H-KING Pages: 10

Brand: Lionel Pages: 2

Ultra Micro FPV Vapor

Brand: E-FLITE Pages: 17

MESSERSCHMITT BF 110 C

Brand: Flying Styro Kit Pages: 16

Lincoln Logs Big L Ranch

Brand: K'Nex Pages: 8

Zoom Ju 87A interior S.A.

Brand: Eduard Pages: 4

Brand: STUDIO27 Pages: 4

TWISTER Rave Hoopz

Brand: Hasbro Gaming Pages: 2

Zero Fighter 52

Brand: BigPlanes Pages: 8

Sing and Soothe Mobile

Brand: VTech Baby Pages: 18

Brand: marklin Pages: 36

Scott Free Offshore

Brand: H-King Marine Pages: 8

Nick Jr. Dora the Explorer DTE516

Brand: Emerson Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands