Panasonic VF200 Instruction Manual Download Page 58

Page: 58 / 289

4. Operation Method (Basic Operation)

4.5 Setting Frequency with Operation Panel

There are 2 modes to set frequency with operation panel as follows.

■

Potentiometer Setting Mode (Parameter P004 is set to “0”: factory setting.)

Adjust the position of potentiometer dial on operation panel to make setting.

MIN. position stands for operation stop (0V stop: see parameter P101), while

MAX. position for the maximum frequency.

■

Digital Setting Mode (Parameter P004 is set to “1”.)

Press MODE button on the panel to enter frequency setting mode (display: Fr);

press SET button and display the frequency to be set by pressing UP and DOWN

buttons and then press SET button again to complete the setting. Also, the

following “MOP function” can be used for frequency setting during operation.

MOP function

The frequency can be changed by pressing and holding UP or DOWN button

during operation. However, if parameter P003 is set to “1”, this function does not

work.

The operation will vary according to the settings of “Parameters” P154: MOP

Function Select” and “P155: MOP Operation Acceleration/Deceleration Time”.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands