Panasonic VF200 Instruction Manual Download Page 63

Page: 63 / 289

4. Operation Method (Basic Operation)

■

Operating Example

②

: Reverse run operation at operating frequency of 25

1. Turn on the power.

The display part will be ON immediately after power-on.

(Operation Status Display Mode)

2. Change rotation direction.

Press

button twice successively.

Press

button. (The display part is flickering.)

Press

button. (The display part is flickering.)

Press

button to set data.

(Return to Operation Status Display Mode.)

3. Start operation.

Press

button. The inverter enters operation status, but it

can be only in 0V stop status due to the frequency setting dial

is in the MIN. position.

4. Adjust frequency.

Turn the frequency setting dial

clockwise slowly till the

value “25.0” appears.The motor starts to run. The value “25.0”

indicates that the motor is running at 25 Hz.

5. Input stop command.

Press

button. The motor starts to decelerate till to stop.

■

Operating Example

③

: Changing rotation direction during operation

The operations are the same as “Changing rotation direction” shown in the above

example. But in this case, as the SET button is pressed in the final procedure, the

display will be switched to Operation Status Display Mode and the motor will

rotate in reverse direction with deceleration.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands