Panasonic VF200 Instruction Manual Download Page 183

Page: 183 / 289

Appendix Function Parameter List

■

JOG Function

Micro operations such as position adjustment can be performed with external

control signals.

Signal input terminals for controlling micro operation from external devices

can be set with parameter P036 to P040.

But Run Command Select (parameter P003) should be set through external

control.

・

Turn the signal input ON, and it will enter JOG operation mode.

・

JOG operation is performed according to “P042: JOG Frequency”, “P043:

JOG Acceleration Time” and “P044: JOG Deceleration Time” settings, after

run/stop and forward/reverse run signals are input with terminal No.2 and

No.3.

< Example > When SW1 (parameter P036 = 3) is set to JOG function and run

command select (parameter P003 = 2) is used

Note 1) During JOG operation, please turn the JOG select signal ON (time B)

and then turn the run signal ON.

Note 2) During reverse run operation, please turn the reverse run signal ON

(time A) and then turn the run signal ON.

Related parameters: P042 to P044

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands