Panasonic VF200 Instruction Manual Download Page 224

Page: 224 / 289

Appendix Function Parameter List

217

P095

P096

Current Sensing Level
Current Sensing Delay Time

Open-collector 1, 2 and relay output can be used to set current sensing level

and delay time when current sensing signal is output.

■

Parameter P095: Current Sensing Level

Data setting range (A) 0.1 to 100.0

■

Parameter P096: Current Sensing Delay Time

Data setting range (s) 0.1 to 10.0

・

Current sensing delay time refers to the delay time for a signal to switch from

OFF to ON.

The delay time for a signal to switch from ON to OFF is about 100 ms (fixed

value).

Related parameters: P090 to P092

P097

Analog and PWM Output Function Select

Functions of “0 to 10 V voltage signal” and “output state signal (PWM)” output

from control circuit terminal No.17 and terminal No.10 to No.12 can be set

respectively.

Setting

value

Details

Signals in proportion to output

frequency are output.

Signals in proportion to output

current are output.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands