Panasonic VF200 Instruction Manual Download Page 233

Page: 233 / 289

Appendix Function Parameter List

■

Parameter P109: Derivative Time [Td]

Data setting range (s) 0000

0.1 to 3600

* “0000” indicates that there is no derivative control.

■

Parameter P110: Control Cycle [Ts]

Data setting range (s) 0.01 to 60.00

■

Parameter P111: PID Target Value

Data setting range (%) 0.0

0.1 to 100.0

Related parameters: P004, P036 to P040, P099, P102 to P104, P124 to P127

■

Setting procedures of PID control

1. PID control select

・

“P124: The 2

Analog Input Function Select” is set to “1” or “2”.

“1” and “2” will be treated as “measured value” and “bias signal”

respectively.

・

When parameter P142 = “0” or “3”, PID control will not be performed.

2. Measured value (PV)

・

“P125: The 2

Analog Input Signal Select”

is set to the signal specification of the

detector.

・

The relationship between detector signal

and measured value (PV) is set with “P126:

The 2

Bias Frequency Setting” and “P127:

The 2

Gain Frequency”.

<Example> 4 mA = 0

％

, 20 mA = 100

％

・

Bias can be added with “P157: The 2

Analog Superimposed Value”.

Summary of Contents for VF200


































































































































































































































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Panasonic VF200, Instruction Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands